Qualcomm Technologies, Inc. WCD audio CODEC

WSA macro in Bolero codec

Required properties:
 - compatible = "qcom,wsa-macro";
 - reg: Specifies the WSA macro base address for Bolero
	soundwire core registers.
 - clock-names : clock names defined for WSA macro
 - clocks : clock handles defined for WSA  macro
 - qcom,default-clk-id: Default clk ID used for WSA macro
 - qcom,wsa-swr-gpios: phandle for SWR data and clock GPIOs of WSA macro
 - qcom,wsa-bcl-pmic-params: u8 array of PMIC ID, SID and PPID in same order
			 required to be configured to receive interrupts
			 in BCL block of WSA macro

WSA slave device as child of Bolero codec

Required properties:
 - compatible = "qcom,wsa881x";
 - reg: Specifies the WSA slave device base address.
 - qcom,spkr-sd-n-gpio: speaker reset gpio

Optional properties:
 - bolero-handle: phandle to bolero codec

Example:

&bolero {
	wsa_macro: wsa-macro {
		compatible = "qcom,wsa-macro";
		reg = <0x0C2C0000 0x0>;
		clock-names = "wsa_core_clk", "wsa_npl_clk";
		clocks = <&clock_audio_wsa_1 0>,
		<&clock_audio_wsa_2 0>;
		qcom,wsa-swr-gpios = &wsa_swr_gpios;
		qcom,wsa-bcl-pmic-params = /bits/ 8 <0x00 0x00 0x1E>;
		qcom,default-clk-id = <TX_CORE_CLK>;
		swr_0: wsa_swr_master {
			compatible = "qcom,swr-mstr";
			wsa881x_1: wsa881x@20170212 {
				compatible = "qcom,wsa881x";
				reg = <0x00 0x20170212>;
				qcom,spkr-sd-n-gpio = <&tlmm 80 0>;
				bolero-handle = <&bolero>;
			};
		};
	};
};

VA macro in bolero codec

Required properties:
 - compatible = "qcom,va-macro";
 - reg: Specifies the VA macro base address for Bolero
	soundwire core registers.
 - clock-names : clock names defined for VA macro
 - clocks : clock handles defined for VA macro
 - qcom,default-clk-id: Default clk ID used for VA macro
 - va-vdd-micb-supply： phandle of mic bias supply's regulator device tree node
 - qcom,va-vdd-micb-voltage： mic bias supply's voltage level min and max in mV
 - qcom,va-vdd-micb-current： mic bias supply's max current in mA
 - qcom,va-dmic-sample-rate： Sample rate defined for DMIC connected to VA macro

Optional properties:
 - qcom,va-clk-mux-select： VA macro MCLK MUX selection
 - qcom,va-island-mode-muxsel： VA macro island mode MUX selection
		This property is required if qcom,va-clk-mux-select is provided

Example:

&bolero {
	va_macro: va-macro {
		compatible = "qcom,va-macro";
		reg = <0x0C490000 0x0>;
		clock-names = "va_core_clk";
		clocks = <&clock_audio_va 0>;
		qcom,default-clk-id = <TX_CORE_CLK>;
		va-vdd-micb-supply = <&S4A>;
		qcom,va-vdd-micb-voltage = <1800000 1800000>;
		qcom,va-vdd-micb-current = <11200>;
		qcom,va-dmic-sample-rate = <4800000>;
		qcom,va-clk-mux-select = <1>;
		qcom,va-island-mode-muxsel = <0x033A0000>;
	};
};

RX macro in bolero codec

Required properties:
 - compatible = "qcom,rx-macro";
 - reg: Specifies the Rx macro base address for Bolero
	soundwire core registers.
 - clock-names : clock names defined for RX macro
 - clocks : clock handles defined for RX macro
 - qcom,default-clk-id: Default clk ID used for RX macro
 - qcom,rx-swr-gpios: phandle for SWR data and clock GPIOs of RX macro
 - qcom,rx_mclk_mode_muxsel: register address for RX macro MCLK mode mux select
 - qcom,rx-bcl-pmic-params: u8 array of PMIC ID, SID and PPID in same order
			 required to be configured to receive interrupts
			 in BCL block of WSA macro

Optional properties:
 - qcom,disable-div2-clk-switch: u32 int to disable clock switch for rx master.

Example:

&bolero {
	rx_macro: rx-macro {
		compatible = "qcom,rx-macro";
		reg = <0x62EE0000 0x0>;
		clock-names = "rx_core_clk", "rx_npl_clk";
		clocks = <&clock_audio_rx_1 0>,
			 <&clock_audio_rx_2 0>;
		qcom,rx-swr-gpios = <&rx_swr_gpios>;
		qcom,rx_mclk_mode_muxsel = <0x62C25020>;
		qcom,rx-bcl-pmic-params = /bits/ 8 <0x00 0x00 0x1E>;
		qcom,default-clk-id = <TX_CORE_CLK>;
		swr_1: rx_swr_master {
			compatible = "qcom,swr-mstr";
			wcd938x_rx_slave: wcd938x-rx-slave {
				compatible = "qcom,wcd938x-slave";
			};
		};
	};
};

TX macro in bolero codec

Required properties:
 - compatible = "qcom,tx-macro";
 - reg: Specifies the Tx macro base address for Bolero
	soundwire core registers.
 - clock-names : clock names defined for TX macro
 - clocks : clock handles defined for TX macro
 - qcom,tx-swr-gpios: phandle for SWR data and clock GPIOs of TX macro
 - qcom,tx-dmic-sample-rate: Sample rate defined for DMICs connected to TX macro

Optional properties:
 - compatible = "qcom,swr-mstr";
	- Child of TX macro represent TX SWR master.
 - qcom,swrm-hctl-reg: HW_CTL and CLK_ENABLE bits of SWR module.
                       Need Disable HW_CTL bit(to gate HW control)
                       for particular Soundwire master version as SW workaround.

Example:

&bolero {
	tx_macro: tx-macro {
		compatible = "qcom,tx-macro";
		reg = <0x62EC0000 0x0>;
		clock-names = "tx_core_clk", "tx_npl_clk";
		clocks = <&clock_audio_tx_1 0>
			 <&clock_audio_tx_2 0>;
		qcom,tx-swr-gpios = <&tx_swr_gpios>;
		qcom,tx-dmic-sample-rate = <4800000>;
		swr_2: tx_swr_master {
			compatible = "qcom,swr-mstr";
			qcom,swrm-hctl-reg = <0xa53a400>;
			wcd938x_tx_slave: wcd938x-tx-slave {
				compatible = "qcom,wcd938x-slave";
			};
			rouleur_tx_slave: rouleur-tx-slave {
				compatible = "qcom,rouleur-slave";
			};
		};
	};
};

&bolero {
	rx_macro: rx-macro {
		compatible = "qcom,tx-macro";
		reg = <0x62EC0000 0x0>;
		clock-names = "rx_core_clk", "rx_npl_clk";
		clocks = <&clock_audio_rx_1 0>
			 <&clock_audio_rx_2 0>;
		qcom,rx-swr-gpios = <&rx_swr_gpios>;
		swr_2: rx_swr_master {
			compatible = "qcom,swr-mstr";
			wcd937x_rx_slave: wcd937x-rx-slave {
				compatible = "qcom,wcd937x-slave";
			};
			rouleur_rx_slave: rouleur-rx-slave {
				compatible = "qcom,rouleur-slave";
			};
		};
	};
};

Tanggu Codec

Required properties:
 - compatible: "qcom,wcd937x-codec";
 - qcom,rx_swr_ch_map: mapping of swr rx slave port configuration to port_type and also
		corresponding master port type it need to attach.
		format: <port_id, slave_port_type, ch_mask, ch_rate, master_port_type>
		same port_id configurations have to be grouped, and in ascending order.
 - qcom,tx_swr_ch_map: mapping of swr tx slave port configuration to port_type and also
		corresponding master port type it need to attach.
		format: <port_id,slave_port_type, ch_mask, ch_rate, master_port_type>
		same port_id configurations have to be grouped, and in ascending order.
 - qcom,wcd-rst-gpio-node: Phandle reference to the DT node having codec reset gpio
                        configuration. If this property is not defined, it is
                        expected to atleast define "qcom,cdc-reset-gpio" property.
 - qcom,rx-slave: phandle reference of Soundwire Rx slave device.
 - qcom,tx-slave: phandle reference of Soundwire Tx slave device.

Optional properties:

 - cdc-vdd-rxtx-supply: phandle of rxtx supply's regulator device tree node.
 - qcom,cdc-vdd-rxtx-voltage: rxtx supply's voltage level min and max in mV.
 - qcom,cdc-vdd-rxtx-current: rxtx supply's max current in mA.
 - qcom,cdc-vdd-rxtx-lpm-supported: rxtx supply's LPM mode.

 - cdc-vddio-supply: phandle of io supply's regulator device tree node.
 - qcom,cdc-vddio-voltage: io supply's voltage level min and max in mV.
 - qcom,cdc-vddio-current: io supply's max current in mA.
 - qcom,cdc-vddio-lpm-supported: io supply's LPM mode.

 - cdc-vdd-buck-supply: phandle of buck supply's regulator device tree node.
 - qcom,cdc-vdd-buck-voltage: buck supply's voltage level min and max in mV.
 - qcom,cdc-vdd-buck-current: buck supply's max current in mA.

 - cdc-vdd-mic-bias-supply: phandle of mic bias supply's regulator device tree node.
 - qcom,cdc-vdd-mic-bias-voltage: mic bias supply's voltage level min and max in mV.
 - qcom,cdc-vdd-mic-bias-current: mic bias supply's max current in mA.

 - qcom,cdc-static-supplies: List of supplies to be enabled prior to codec
			     hardware probe.  Supplies in this list will be
			     stay enabled.

 - qcom,cdc-on-demand-supplies: List of supplies which can be enabled
				dynamically.
				Supplies in this list are off by default.

Example:
wcd937x_codec: wcd937x-codec {
	compatible = "qcom,wcd937x-codec";
	qcom,rx_swr_ch_map = <0 HPH_L 0x1 0 HPH_L>,
		<0 HPH_R 0x2 0 HPH_R>, <1 CLSH 0x3 0 CLSH>,
		<2 COMP_L 0x1 0 COMP_L>, <2 COMP_R 0x2 0 COMP_R>,
		<3 LO 0x1 0 LO>, <4 DSD_L 0x1 0 DSD_L>,
		<4 DSD_R 0x2 0 DSD_R>;
	qcom,tx_swr_ch_map = <0 ADC1 0x1 0 ADC1>,
		<1 ADC2 0x1 0 ADC3>, <1 ADC3 0x2 0 ADC4>,
		<2 DMIC0 0x1 0 DMIC0>, <2 DMIC1 0x2 0 DMIC1>,
		<2 MBHC 0x4 0 DMIC2>, <3 DMIC2 0x1 0 DMIC4>,
		<3 DMIC3 0x2 0 DMIC5>, <3 DMIC4 0x4 0 DMIC6>,
		<3 DMIC5 0x8 0 DMIC7>;

	qcom,wcd-rst-gpio-node = <&wcd937x_rst_gpio>;
	qcom,rx-slave = <&wcd937x_rx_slave>;
	qcom,tx-slave = <&wcd937x_tx_slave>;

	cdc-vdd-buck-supply = <&S4A>;
	qcom,cdc-vdd-buck-voltage = <1800000 1800000>;
	qcom,cdc-vdd-buck-current = <650000>;

	cdc-vdd-rxtx-supply = <&S4A>;
	qcom,cdc-vdd-rxtx-voltage = <1800000 1800000>;
	qcom,cdc-vdd-rxtx-current = <30000>;

	cdc-vddio-supply = <&S4A>;
	qcom,cdc-vddio-voltage = <1800000 1800000>;
	qcom,cdc-vddio-current = <30000>;

	cdc-vdd-mic-bias-supply = <&BOB>;
	qcom,cdc-vdd-mic-bias-voltage = <3296000 3296000>;
	qcom,cdc-vdd-mic-bias-current = <30000>;

	qcom,cdc-static-supplies = "cdc-vdd-rxtx",
				   "cdc-vddio";
	qcom,cdc-on-demand-supplies = "cdc-vdd-buck",
				      "cdc-vdd-mic-bias";
};

Traverso Codec

Required properties:
 - compatible: "qcom,wcd938x-codec";
 - qcom,rx_swr_ch_map: mapping of swr rx slave port configuration to port_type and also
		corresponding master port type it need to attach.
		format: <port_id, slave_port_type, ch_mask, ch_rate, master_port_type>
		same port_id configurations have to be grouped, and in ascending order.
 - qcom,tx_swr_ch_map: mapping of swr tx slave port configuration to port_type and also
		corresponding master port type it need to attach.
		format: <port_id,slave_port_type, ch_mask, ch_rate, master_port_type>
		same port_id configurations have to be grouped, and in ascending order.
 - qcom,wcd-rst-gpio-node: Phandle reference to the DT node having codec reset gpio
                        configuration. If this property is not defined, it is
                        expected to atleast define "qcom,cdc-reset-gpio" property.
 - qcom,rx-slave: phandle reference of Soundwire Rx slave device.
 - qcom,tx-slave: phandle reference of Soundwire Tx slave device.

Optional properties:

 - cdc-vdd-rxtx-supply: phandle of rxtx supply's regulator device tree node.
 - qcom,cdc-vdd-rxtx-voltage: rxtx supply's voltage level min and max in mV.
 - qcom,cdc-vdd-rxtx-current: rxtx supply's max current in mA.

 - cdc-vddio-supply: phandle of io supply's regulator device tree node.
 - qcom,cdc-vddio-voltage: io supply's voltage level min and max in mV.
 - qcom,cdc-vddio-current: io supply's max current in mA.

 - cdc-vdd-buck-supply: phandle of buck supply's regulator device tree node.
 - qcom,cdc-vdd-buck-voltage: buck supply's voltage level min and max in mV.
 - qcom,cdc-vdd-buck-current: buck supply's max current in mA.

 - cdc-vdd-mic-bias-supply: phandle of mic bias supply's regulator device tree node.
 - qcom,cdc-vdd-mic-bias-voltage: mic bias supply's voltage level min and max in mV.
 - qcom,cdc-vdd-mic-bias-current: mic bias supply's max current in mA.

 - qcom,cdc-static-supplies: List of supplies to be enabled prior to codec
			     hardware probe.  Supplies in this list will be
			     stay enabled.

 - qcom,cdc-on-demand-supplies: List of supplies which can be enabled
				dynamically.
				Supplies in this list are off by default.

Example:
wcd938x_codec: wcd938x-codec {
	compatible = "qcom,wcd938x-codec";
	qcom,rx_swr_ch_map = <0 HPH_L 0x1 0 HPH_L>,
		<0 HPH_R 0x2 0 HPH_R>, <1 CLSH 0x3 0 CLSH>,
		<2 COMP_L 0x1 0 COMP_L>, <2 COMP_R 0x2 0 COMP_R>,
		<3 LO 0x1 0 LO>, <4 DSD_L 0x1 0 DSD_L>,
		<4 DSD_R 0x2 0 DSD_R>;
	qcom,tx_swr_ch_map = <0 ADC1 0x1 0 ADC1>,
		<1 ADC2 0x1 0 ADC3>, <1 ADC3 0x2 0 ADC4>,
		<2 DMIC0 0x1 0 DMIC0>, <2 DMIC1 0x2 0 DMIC1>,
		<2 MBHC 0x4 0 DMIC2>, <3 DMIC2 0x1 0 DMIC4>,
		<3 DMIC3 0x2 0 DMIC5>, <3 DMIC4 0x4 0 DMIC6>,
		<3 DMIC5 0x8 0 DMIC7>;

	qcom,wcd-rst-gpio-node = <&wcd938x_rst_gpio>;
	qcom,rx-slave = <&wcd938x_rx_slave>;
	qcom,tx-slave = <&wcd938x_tx_slave>;

	cdc-vdd-buck-supply = <&S4A>;
	qcom,cdc-vdd-buck-voltage = <1800000 1800000>;
	qcom,cdc-vdd-buck-current = <650000>;

	cdc-vdd-rxtx-supply = <&S4A>;
	qcom,cdc-vdd-rxtx-voltage = <1800000 1800000>;
	qcom,cdc-vdd-rxtx-current = <30000>;

	cdc-vddio-supply = <&S4A>;
	qcom,cdc-vddio-voltage = <1800000 1800000>;
	qcom,cdc-vddio-current = <30000>;

	cdc-vdd-mic-bias-supply = <&BOB>;
	qcom,cdc-vdd-mic-bias-voltage = <3296000 3296000>;
	qcom,cdc-vdd-mic-bias-current = <30000>;

	qcom,cdc-static-supplies = "cdc-vdd-rxtx",
				   "cdc-vddio";
	qcom,cdc-on-demand-supplies = "cdc-vdd-buck",
				      "cdc-vdd-mic-bias";
};

Bolero Clock Resource Manager

Required Properties:
 - compatible = "qcom,bolero-clk-rsc-mngr";
 - qcom,fs-gen-sequence: Register sequence for fs clock generation
 - clock-names : clock names defined for WSA macro
 - clocks : clock handles defined for WSA  macro

Optional Properties:
 - qcom,rx_mclk_mode_muxsel: register address for RX macro MCLK mode mux select
 - qcom,wsa_mclk_mode_muxsel: register address for WSA macro MCLK mux select
 - qcom,va_mclk_mode_muxsel: register address for VA macro MCLK mode mux select

Example:
&bolero {
	bolero-clock-rsc-manager {
		compatible = "qcom,bolero-clk-rsc-mngr";
		qcom,fs-gen-sequence = <0x3000 0x1>,
				<0x3004 0x1>, <0x3080 0x2>;
		qcom,rx_mclk_mode_muxsel = <0x033240D8>;
		qcom,wsa_mclk_mode_muxsel = <0x033220D8>;
		qcom,va_mclk_mode_muxsel = <0x033A0000>;
		clock-names = "tx_core_clk", "tx_npl_clk", "rx_core_clk",
			"rx_npl_clk", "wsa_core_clk", "wsa_npl_clk",
			"va_core_clk", "va_npl_clk";
		clocks = <&clock_audio_tx_1 0>, <&clock_audio_tx_2 0>,
			<&clock_audio_rx_1 0>, <&clock_audio_rx_2 0>,
			<&clock_audio_wsa_1 0>, <&clock_audio_wsa_2 0>,
			<&clock_audio_va_1 0>, <&clock_audio_va_2 0>;
	};
};

WSA Analog Codec

Required Properties:
 - compatible = "qcom,wsa881x-i2c-codec";
 - reg: Specifies the I2C chip address.
 - clock-names : clock names defined for WSA master clock
 - clocks : clock handles defined for WSA master clock
 - qcom,wsa-analog-clk-gpio: Specificies WSA_MCLK GPIO handle
 - qcom,wsa-analog-reset-gpio: Specifies WSA reset GPIO handle

Optional Properties:
 - qcom,wsa-analog-vi-gpio: Specifies WSA VI sense GPIO handle

Example:
&qupv3_se1_i2c {
	wsa881x_i2c_f: wsa881x-i2c-codec@f {
		compatible = "qcom,wsa881x-i2c-codec";
		reg = <0x0f>;
		clock-names = "wsa_mclk";
		clocks = <&wsa881x_analog_clk 0>;
		qcom,wsa-analog-clk-gpio = <&wsa881x_analog_clk_gpio>;
		qcom,wsa-analog-reset-gpio = <&wsa881x_analog_reset_gpio>;
	};

	wsa881x_i2c_45: wsa881x-i2c-codec@45 {
		compatible = "qcom,wsa881x-i2c-codec";
		reg = <0x045>;
	};
};

WSA883x Soundwire slave device as child of Soundwire master in Bolero codec

Required properties:
 - compatible = "qcom,wsa883x";
 - reg: Specifies the WSA883x soundwire slave unique device address
 - qcom,spkr-sd-n-gpio: speaker reset gpio

Optional properties:
 - bolero-handle: phandle to bolero codec
 - cdc-vdd-1p8-supply: phandle of VDD 1.8V supply's regulator device tree node.
 - qcom,cdc-vdd-1p8-voltage: VDD 1.8V supply's voltage level min and max in mV.
 - qcom,cdc-vdd-1p8-current: VDD 1.8V supply's max current in mA.
 - qcom,cdc-vdd-qp8-lpm-supported: VDD 1.8V supply's LPM mode.
 - qcom,cdc-static-supplies: List of supplies to be enabled prior to codec
			     hardware probe.  Supplies in this list will be
			     stay enabled.

Example:
wsa883x_0221: wsa883x@02170221 {
	compatible = "qcom,wsa883x";
	reg = <0x02 0x02170221>;
	qcom,spkr-sd-n-gpio = <&tlmm 80 0>;
	bolero-handle = <&bolero>;

	cdc-vdd-1p8-supply = <&S10B>;
	qcom,cdc-vdd-1p8-voltage = <1800000 1800000>;
	qcom,cdc-vdd-1p8-current = <20000>;
	qcom,cdc-static-supplies = "cdc-vdd-1p8";
};

PM2250 SPMI node

pm2250_spmi: Child node of SPMI bus required for rouleur codec
	     in order to access SPMI register to reset the peripheral.

Required properties:
 -compatible: "qcom,pm2250-spmi";

&spmi_bus {
                pm2250_cdc: qcom,pm2250-cdc {
                        compatible = "qcom,pm2250-spmi";
                };
};


Rouleur Codec

Required properties:
 - compatible: "qcom,rouleur-codec";
 - qcom,split-codec: Property to check on split codec support.
 - qcom,rx_swr_ch_map: mapping of swr rx slave port configuration to port_type and also
		corresponding master port type it need to attach.
		format: <port_id, slave_port_type, ch_mask, ch_rate, master_port_type>
		same port_id configurations have to be grouped, and in ascending order.
 - qcom,tx_swr_ch_map: mapping of swr tx slave port configuration to port_type and also
		corresponding master port type it need to attach.
		format: <port_id,slave_port_type, ch_mask, ch_rate, master_port_type>
		same port_id configurations have to be grouped, and in ascending order.
 - qcom,pmic-spmi-node: Phandle reference to the PMIC SPMI DT node.
 - qcom,wcd-reset-reg: Reset register address in PMIC for rouleur codec.
 - qcom,rx-slave: phandle reference of Soundwire Rx slave device.
 - qcom,tx-slave: phandle reference of Soundwire Tx slave device.

Optional properties:

 - cdc-pa-vpos-supply: phandle of pa vpos supply's regulator device tree node.
 - qcom,cdc-pa-vpos-voltage: pa vpos supply's voltage level min and max in mV.
 - qcom,cdc-pa-vpos-current: pa vpos supply's max current in mA.

 - cdc-vdd-io-supply: phandle of io supply's regulator device tree node.
 - qcom,cdc-vdd-io-voltage: io supply's voltage level min and max in mV.
 - qcom,cdc-vdd-io-current: io supply's max current in mA.

 - cdc-vdd-cp-supply: phandle of vdd cp supply's regulator device tree node.
 - qcom,cdc-vdd-cp-voltage: vdd cp supply's voltage level min and max in mV.
 - qcom,cdc-vdd-cp-current: vdd cp supply's max current in mA.

 - cdc-vdd-mic-bias-supply: phandle of mic bias supply's regulator device tree node.
 - qcom,cdc-vdd-mic-bias-voltage: mic bias supply's voltage level min and max in mV.
 - qcom,cdc-vdd-mic-bias-current: mic bias supply's max current in mA.
 - qcom,cdc-vdd-mic-bias-lpm-supported: mic bias supply's LPM mode.

 - qcom,cdc-static-supplies: List of supplies to be enabled prior to codec
			     hardware probe.  Supplies in this list will be
			     stay enabled.

 - qcom,cdc-on-demand-supplies: List of supplies which can be enabled
				dynamically.
				Supplies in this list are off by default.

Example:

	rouleur_codec: rouleur-codec {
		compatible = "qcom,rouleur-codec";
		qcom,split-codec = <1>;
		qcom,pmic-spmi-node = <&pm2250_cdc>;
		qcom,wcd-reset-reg = <0x0000F3DB>;
		qcom,rx_swr_ch_map = <0 HPH_L 0x1 0 HPH_L>,
			<0 HPH_R 0x2 0 HPH_R>, <1 CLSH 0x1 0 CLSH>,
			<2 COMP_L 0x1 0 COMP_L>, <2 COMP_R 0x2 0 COMP_R>,
			<3 LO 0x1 0 LO>, <4 DSD_L 0x1 0 DSD_L>,
			<4 DSD_R 0x2 0 DSD_R>;
		qcom,tx_swr_ch_map = <0 ADC1 0x1 0 ADC1>,
			<0 ADC2 0x2 0 ADC2>, <0 DMIC0 0x4 0 ADC3>,
			<0 MBHC 0x8 0 ADC4>, <1 DMIC0 0x1 0 DMIC0>,
			<1 DMIC1 0x2 0 DMIC1>, <1 ADC1 0x4 0 DMIC2>,
			<1 MBHC 0x8 0 DMIC3>;

		qcom,rx-slave = <&rouleur_rx_slave>;
		qcom,tx-slave = <&rouleur_tx_slave>;

		cdc-vdd-io-supply = <&L15A>;
		qcom,cdc-vdd-io-voltage = <1800000 1800000>;
		qcom,cdc-vdd-io-current = <10000>;

		cdc-vdd-cp-supply = <&S4A>;
		qcom,cdc-vdd-cp-voltage = <2040000 2040000>;
		qcom,cdc-vdd-cp-current = <300000>;

		cdc-pa-vpos-supply = <&S4A>;
		qcom,cdc-pa-vpos-voltage = <2040000 2040000>;
		qcom,cdc-pa-vpos-current = <2400000>;

		cdc-vdd-mic-bias-supply = <&L22A>;
		qcom,cdc-vdd-mic-bias-voltage = <3304000 3304000>;
		qcom,cdc-vdd-mic-bias-current = <50000>;
		qcom,cdc-vdd-mic-bias-lpm-supported = <1>;

		qcom,cdc-micbias1-mv = <1800>;
		qcom,cdc-micbias2-mv = <1800>;
		qcom,cdc-micbias3-mv = <1800>;

		qcom,cdc-static-supplies = "cdc-vdd-cp",
					   "cdc-vdd-io";
		qcom,cdc-on-demand-supplies = "cdc-pa-vpos",
					      "cdc-vdd-mic-bias";
	};
};
